ridgeway grandfather clock serial number 89006344

Ridgeway grandfather clock serial number 89006344 serial number#

Geben Sie diese Nummer ber Ihrem Namen im Anschriftsblock an. Ridgeway Clocks obligation under this warranty shall be limited to repairing the product with new or renewed components or, at its option, replacing it with a new or renewed product. MOVE CHIME SELECTION LEVER ONLY WHEN MINUTE HAND IS IN Some models play only the Westminster chime, while others give you a selection SAFE TIME AREA of three melodies.ĬAUTION: When performing this operation be careful not to scratch the hand nut, hand or dial.Ĭhime tone may be affected by the hammers resting on the chime rods or striking the rods HAMMER off center.Īlthough the hammers were set at the factory, it is possible for them to get out of adjustment. Insert the crank into the crank holes located in the dial face (See figure 15), and turn the crank CRANK counterclockwise. Problems with the clocks can be related to the clock not running, the clock not chiming or striking, weights not falling at the same time and problems turning the moon. The mechanical clocks are manufactured in the United States. The product information label is located in several locations: outside the shipping carton, back of door, back of the clock, top of the clock, inside the top back corner of the clock, or inside the clock above the back of the dial.įLOOR CLOCK: Cables with pulleys Weights that are suspended by cables with pulleys should be raised by using the crank provided. Ridgeway Furniture Company has been making grandfather clocks exclusively since 1960.

Ridgeway grandfather clock serial number 89006344 serial number#

PRODUCT INFORMATION LABEL The clock model number and serial number are essential for obtaining parts or service. Ridgeway Clocks S Serial Number Are Essential The total weight of each weight is slightly different and each WEIGHT MUST BE INSTALLED IN ITS CORRECT LOCATION FOR THE CLOCK TO OPERATE PROPERLY.

The bottom of each weight is labeled as to its proper hanging position as you view your clock from the front. You can remove the styrofoam blocks AFTER they become loose through normal operation, which typically occurs after eight (8) hours of run time.ĬHIME HAMMERS Also, within the shipping carton will be the clock pendulum packaged in a separate FOAM PAD.

This box contains: a) a key to fit your clock door, b) a crank which will be used to wind your clock and, c) weights which operate the clock movement.

Ridgeway Clocks S Serial Number Are Essential.

search for models between 120 and 300 and i think you'll find itĬreate an account or login in order to post a comment. My clock is a Ridgeway from 1973 (I believe) and it looks close to yours ,Model 144. Do you have a photo of the entire clock or do you just have the top? Good luck. Hopefully someone more familiar with Ridgeway Clocks will come along. 'Tempus Fugit' (or Time Flies) became popular in the 1960's so without more information my guess would be circa 1965 give or take 10 years but that's just a guess. Well, we know that Ridgeway/Gravely didn't start until 1926. 4844 pl85cm are the only numbers on the clock I looked all over even taking off the back panel again. They said that without a serial number they really could only guess it to early 1900s to 1960s. Thanks Bruce99! I have tried contacting them but I need a serial number for them.Ĭould they tell you where to look for it, or does you clock just not have one?

Thanks for sharing and good luck with your research. You should try to contact them to see if they are able and willing to help. They started producing Grandfather Clocks exclusively in 1960. RO6G Clock Parts Supplies for Ridgeway Grandfather Clock Door Key for Clocks Prior to 2004 for Clocks Repair, Wall Clocks, Alarm Clock. It seems that Ridgeway Grandfather Clocks began as the Gravely Furniture Company in 1926.

This is an interesting piece you're sharing with us.